Advanced Metallization and Interconnect Systems for Ulsi by R. Cheung, J. Klein, K. Tsubouchi, M. Murakami, N. Kobayashi

By R. Cheung, J. Klein, K. Tsubouchi, M. Murakami, N. Kobayashi

Show description

By R. Cheung, J. Klein, K. Tsubouchi, M. Murakami, N. Kobayashi

Show description

Read or Download Advanced Metallization and Interconnect Systems for Ulsi Applications in 1997 PDF

Best metallurgy books

Corrosion Under Insulation (CUI) Guidelines (EFC)

Corrosion-under-insulation (CUI) refers back to the exterior corrosion of piping and vessels that happens beneath externally clad/jacketed insulation as a result penetration of water. by means of its very nature CUI has a tendency to stay undetected till the insulation and cladding/jacketing is got rid of to permit inspection or while leaks happen.

Corrosion of Magnesium Alloys (Woodhead Publishing in Materials)

Using magnesium alloys is expanding in more than a few purposes, and their attractiveness is becoming anywhere light-weight fabrics are wanted. This ebook presents a finished account of the corrosion of magnesium alloys. It covers not just the corrosion performances and mechanisms of Mg alloys in traditional environments, equivalent to sodium chloride options, but in addition seems at their corrosion behaviors in designated media, like engine coolants and simulated physique fluids.

The Alloy Tree. A Guide to Low-Alloy Steels, Stainless Steels and Nickel-base Alloys

There are specific key alloys, stainless steels, nickel alloys and coffee alloy steels which are of paramount significance to the facility iteration, petrochemical and oil and fuel industries. in a single totally entire consultant, The alloy tree addresses the importance of such alloys and their position in those basic industries.

Heat Treatment, Selection, and Application of Tool Steels 2E

In a number of brief years, this has turn into the validated reference for instrument makers, warmth treaters, and engineers looking step by step recipes for correctly warmth treating a variety of instrument steels, plus useful information regarding machinability, surprise resistance, put on, and lengthening instrument existence. Now, the thoroughly revised and elevated moment version of this best-selling identify is out there.

Additional info for Advanced Metallization and Interconnect Systems for Ulsi Applications in 1997

Example text

Appendix G also provides guidance on the assessment of nozzles, flanges and shell regions near geometric discontinuities. Section G-2400 provides recommendations on hydrostatic test temperatures (RT,^ + 60°F for vessels before loading fuel, and temperatures based on applied stress intensities in the region of postulated flaws after fuel has been loaded). 4. ASME XI APPENDIX A (ANALYSIS OF FLAWS) (1989 (5)) This Appendix (5) provides a procedure for determining the acceptability of flaws that have been detected during in-service inspection (excluding pre-service inspection) that exceed the allowable flaw indication standards of IWB-3500.

20 of API 5L describe the number, location and orientation of test specimens, as well as retest procedures. Appendix E of API 5L describes supplementary toughness requirements. 5", transverse Charpy specimens are required to be tested at 50°F or less, with a requirement of 60% shear fracture appearance (average of 3 65 specimens) and 80% all heat average. Retesting procedures are described, as well as the number, location and orientation of test specimens, and sub-size Charpy testing. Impact energies are required, as specified by the purchaser.

Lb PSL1 PSL2 PSL3 15 15 15 15 15 15 15 15 1o 0 Lateral expansion, in. 015 | | | | The production specification levels (PSL1 to 3), defined in Section 103 and Appendix A of API 6A, refer to increasing levels of quality and service ratings. Temperature classifications K, L, P, R, S, T and U refer to the following temperature ranges, respectively: -70 to 180°F, -50 to 180°F, -20 to 180°F, room temperature, 0 to 150°F, 0 to 180°F and 0 to 250°F. The number, location and orientation of test specimens are described in Sections 403 and 404 of API 6A, as well as retest procedures and sub-size Charpy requirements.

Download PDF sample

Rated 4.65 of 5 – based on 40 votes